\u5831\u8b66 & \u7570\u5e38 \u5217\u8868 (\u7570\u5e38)<\/p>\n
8600 Ceiling door open\/close limit SW NG
\nFor the door interlock type S spec, a ceiling door open
\n\/close confirmation limit switch failed.<\/p>\n
8601 ATC tool change arm inverter failure
\nATC tool change arm inverter error signal (iAIVAL_B) turned off
\n.<\/p>\n
8602 Chip pan cover interlock
\n[Code]
\n1->At the time of NC running OR loader automatic operating,
\na chip pan cover is not close status.<\/p>\n
8603 C-axis clamp \/ unclamp condition
\n[Code]
\n1->C-axis is not low-pressure brake condition while
\nC-axis cutting feed.<\/p>\n
8604 Long tool change protection
\n[Code]
\n1->The cover open\/close command is
\ndesignated while the spindle is rotating.
\n2->The cover open\/close command is
\ndesignated when the M-tool spindle is rotating.
\n3->The cover open\/close command is
\ndesignated when the C-axis is rotating.
\n4->The cover open\/close command is designated
\nwhile the turret is not at the travel end of Z-axis
\n5->The cover open\/close command is
\ndesignated when the slider was not retract position.
\n6->The slider advance\/retract command is
\ndesignated when the cover was not open position.
\n7->The gripper open\/close command is designated
\nwhen the slider was not advance\/retract position.
\n8->The ATC command(M06,M288,M321,M421) is designated
\nwhen the Long tool was the turret tool.
\n11->The cover was not closed position during Spindle rotation.
\nor, Spindle rotation command was designated when the
\ncover was not closed position.
\n12->The cover was not closed position during M-spindle
\nrotation. or, M-spindle rotation command was designated
\nwhen the cover was not closed position.
\n13->The cover was not closed position during C-axis movement.
\nor, C-axis movement command was designated when the cover
\nwas not closed position.
\n14->The cover was not closed position during axis movement.
\nor, axis movement command was designated when the cover
\nwas not closed position.
\n15->The cover was not closed position during turret indexing.
\nor, turret index command was designated when the
\ncover was not closed position.<\/p>\n
8605 Drive belt disconnection
\nThe drive belt disconnected it.
\n[Code]
\n1->The Belt snap signal of EZ-axis kept OFF for the time of
\nMC SYSTEM PARAMETER ATC “Belt disconnection detect timer
\n(EZ)” setting or longer.
\n2->In the case of matrix magazine specification,the belt
\nsnap signal of MGB-axis kept OFF for the time of MC
\nSYSTEM PARAMETER ATC “Belt disconnection detect
\ntimer(MGB)” setting or longer.<\/p>\n
8606 APC Door open\/close limit N.G.
\nWhen the power is supplied, the open\/close end limit
\nswitches of the operator door or front door are both
\nON or OFF.
\n[Probable Faulty Locations]
\n1)Malfunction of door open\/close end limit switches
\n[Measures to Take]
\n1)Check and replace a faulty door open\/close end limit
\nswitch.<\/p>\n
8607 XB cover interfered
\nThe monitored axis entered the interference range when
\nXB cover for B-turret was not specified position. Or,
\nXB cover was not specified position when the monitored
\naxis was entering.
\n[Code]
\n1-> Sub-spindle or H1 turret<\/p>\n
8608 Touch setter unit illegal
\n[Code]
\nNone->Touch setter unit illegal signal kept OFF for a second
\nor longer ,when touch setter was not retract position.<\/p>\n
8680 \u5340\u57df\u50b3\u611f\u5668\u4e92\u9396
\n\u9580\u5340\u57df\u50b3\u611f\u5668\u5b89\u88dd\u898f\u683c\u4e2d\uff0c\u56e0\u5340\u57df\u50b3\u611f\u5668\u906e\u64cb\u88ab\u7981\u6b62\u7528\u906e\u64cb\u5340\u57df
\n\u50b3\u611f\u5668\u64cd\u4f5c\u3002
\n[\u4ee3\u78bc]
\n1->\u7576\u524d\u9580\u672a\u95dc\u6642\uff0c\u88dd\u6599\u5668\u904b\u884c\u4e2d\u5340\u57df\u50b3\u611f\u5668\u70ba\u95dc\u3002
\n\u6216\u88dd\u6599\u5668\u5728\u5340\u57df\u50b3\u611f\u5668\u4fe1\u865f\u70ba\u95dc\u6642\u8d77\u52d5\u904b\u884c\u3002
\n2->\u7576\u524d\u9580\u672a\u95dc\u6642\uff0c\u88dd\u6599\u5668\u8ef8\u4eba\u5de5\u904b\u884c\u4e2d\u5340\u57df\u50b3\u611f\u5668\u70ba\u95dc\u3002<\/p>\n","protected":false},"excerpt":{"rendered":"